[OpenWrt Wiki] Xiaomi Redmi AX6 Wi-Fi 6 Mesh Router (2024)

  • The sysupgrade command may fail due to a random issue of wpad not being effectively stopped while upgrading Openwrt. Stopping the wpad service with service wpad stop before doing the sysupgrade fixes the issue.

  • Ath11k memory: The ath11k driver needed for the main wireless radios uses a lot of memory when there are few stations connected and low bandwidth traffic flowing.

  • NSS acceleration: the Qualcom NSS hardware acceleration is not available and maybe never will be. There is a community effort to enable it in the forum but this does not guarantee that it will be officially supported in the future.

  • The IPQ807x target has not yet support for DSA, on OpenWrt: See this forum post. The regular DSA instructions on the mini tutorial do demonstrably work however; wireless interfaces need to be set up in the Network→Wireless section and then be bridged in their Interface Configuration→General Setup→Network menu to connect them to wired interfaces, and the contributor making this statement only uses tagged VLANs on the wired ports.

Snapshot versions don't have luci installed. If you want it, you can create your own customized firmware using for example the Firmware selector or you can install the package once installed (look at this guide LuCI essentials).

To flash this image there is a need for SSH access to the OEM firmware. It is not possible for now to flash OpenWrt from the stock FW with the OpenWrt Factory image.To gain SSH access, you will need a second router (any device) with OpenWrt firmware (further refered to as Router B).

Redmi AX6 can be recovered from a soft-brick with TFTP. The flow is:

  • The router boots and asks for an IP address on the LAN ports via DHCP

  • The TFTP server assigns an IP address to the router

  • The router then connects to the TFTP server (where your DHCP server listen, e.g.: 192.168.31.100) and tries to download a file named with the IP address given by the DHCP server converted to hexadecimal.

Because of this quirk we will have to configure the tftp server to assign only one IP and we will set the file name to the only IP address it can receive.

For Windows you can use tftpd64 and on Linux you can use dnsmasq.These are the steps to do it for Linux (this can be adapted to the tftpd64's graphical interface very easily):

  • Obtain the name of the ethernet adapter (to be used in further steps):

    ip link
  • The result will loke something like (in this case, the name of the ethernet adapter is enp2s0):

    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:002: enp2s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP mode DEFAULT group default qlen 1000 link/ether xx:xx:xx:xx:xx:xx brd ff:ff:ff:ff:ff:ff3: wlp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DORMANT group default qlen 1000 link/ether yy:yy:yy:yy:yy:yy brd ff:ff:ff:ff:ff:ff
  • Set a static address on your PC to serve the firmware from:

    sudo ip address flush dev <adapter name>sudo ip address add 192.168.31.100/24 dev <adapter name>
  • Run the server with the following command:

    sudo dnsmasq --no-daemon --listen-address=192.168.31.100 --bind-interfaces --dhcp-range=192.168.31.2,192.168.31.254 --enable-tftp --tftp-root=/tmp/tftp --log-dhcp --log-facility=-
  • Unplug the power, press and hold the reset button, plug the power back while still holding the button.

    • Hold the reset button until the router's LED starts flashing orange.

    • then it goes solid orange again, release the button.

    • If in the terminal, you see that the router requests a different firmware file (different name; if you have previously had a Xiaomi firmware v.1.1.14 on the router), rename the file in the tmp folder and repeat the procedures from the IP flush again.

  • When the device finished loading the firmware, the led starts flashing with orange (amber) light. Wait for until blue led to goes solid!

    • It might take some time for the led to go solid blue

    • If the recovery doesn't accept the downloaded file the led switches to solid white - if this is the case, restart the recovery process with other file

    • If the led is blinking blue led it means the device was flashed successfully and can be restarted

  • Put your interface back to DHCP mode and start again with breaking your device

Architecture AArch64
Vendor Qualcomm
Bootloader U-Boot 2016.01 (Jul 10 2020 - 05:56:17 +0000)
System-On-Chip 4x ARM Cortex A53 (IPQ8071A / QCA8074 V2)
CPU/Speed Up to 1.4 GHz
Flash-Chip ESMT F59D1G81MB-AZM1P9ACX
Flash size 128 MB
RAM 512MB DDR3 (EM6HE16EWAKG-10H)
Wireless 5G QCN5054 4×4 MIMO 80MHz 2×2 MIMO 160MHz / 2.4G QCN5024 2×2 MIMO 573Mbps (CPU restricted).
Wireless features RX LDPC, TX STBC, SUBF, MUBF (2.4GHz 2 streams; 5GHz 4 streams), 160/80+80MHz
Wireless features 5GHz FEM: QPF4550 (+20.5dBm MCS9VHT80); 2.4GHz FEM: QPF4200 (+21dBm MCS9VHT40; +22.5dBm MCS7VHT40 )
Ethernet 1 - 10/100/1000M adaptive WAN port (Auto MDI/MDIX); 3 - 10/100/1000M adaptive LAN ports (Auto MDI/MDI×)
Switch Qualcomm QCA8075
USB No
Serial Yes
JTAG Not populated

Redmi AX6 front PCB

Redmi AX6 back PCB

Redmi AX6 RF frontend comparison

To open the case, first remove the sticker from the bottom of the device. Two phillips screws are holding it together. After removing the screws, there are still plastic claws around the top piece and the edge. Gently use a guitar pick or similar tool to start separating the top piece around the edge.

Serial port pinout is clearly marked on the board.

Note: It's been reported the device uses 1.8V.

TTL serial connection is possible, the header has to be soldered, no missing components (resistors etc). There is 5 seconds to enter the bootloader (press ENTER).

Serial connection parameters for Xiaomi Redmi AX6 TTL, 115200, 8N1

Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147S - IMAGE_VARIANT_STRING=HAACANAAAS - OEM_IMAGE_VERSION_STRING=xiaoyang-gvS - Boot Config, 0x000002e5B - 201 - PBL, StartB - 2738 - bootable_media_detect_entry, StartB - 3444 - bootable_media_detect_success, StartB - 3449 - elf_loader_entry, StartB - 6112 - auth_hash_seg_entry, StartB - 6355 - auth_hash_seg_exit, StartB - 68488 - elf_segs_hash_verify_entry, StartB - 131189 - PBL, EndB - 141794 - SBL1, StartB - 194071 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4B - 200476 - pm_device_init, StartB - 320890 - PM_SET_VAL:SkipD - 119743 - pm_device_init, DeltaB - 323178 - pm_driver_init, StartD - 5368 - pm_driver_init, DeltaB - 329613 - clock_init, StartD - 2135 - clock_init, DeltaB - 333670 - boot_flash_init, StartD - 11895 - boot_flash_init, DeltaB - 349255 - boot_config_data_table_init, StartD - 3202 - boot_config_data_table_init, Delta - (575 Bytes)B - 356758 - Boot Setting : 0x00000600B - 360693 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16B - 367647 - sbl1_ddr_set_params, StartB - 371459 - CPR configuration: 0x300B - 374845 - cpr_init, StartB - 377712 - Rail:0 Mode: 5 Voltage: 808000B - 382866 - CL CPR settled at 760000mVB - 385703 - Rail:1 Mode: 5 Voltage: 880000B - 389881 - Rail:1 Mode: 7 Voltage: 912000D - 16470 - cpr_init, DeltaB - 396774 - Pre_DDR_clock_init, StartB - 400800 - Pre_DDR_clock_init, EndB - 404186 - DDR Type : PCDDR3B - 409798 - do ddr sanity test, StartD - 1037 - do ddr sanity test, DeltaB - 414647 - DDR: Start of HAL DDR Boot TrainingB - 419375 - DDR: End of HAL DDR Boot TrainingB - 425048 - DDR: Checksum to be stored on flash is -403985928B - 435387 - Image Load, StartD - 224328 - QSEE Image Loaded, Delta - (1373936 Bytes)B - 659806 - Image Load, StartD - 61 - SEC Image Loaded, Delta - (0 Bytes)B - 667462 - Image Load, StartD - 10736 - DEVCFG Image Loaded, Delta - (26004 Bytes)B - 678289 - Image Load, StartD - 25254 - RPM Image Loaded, Delta - (105964 Bytes)B - 703604 - Image Load, StartD - 96655 - APPSBL Image Loaded, Delta - (590228 Bytes)B - 800381 - QSEE Execution, StartD - 61 - QSEE Execution, DeltaB - 806206 - USB D+ check, StartD - 0 - USB D+ check, DeltaB - 812581 - SBL1, EndD - 673105 - SBL1, DeltaS - Flash Throughput, 6753 KB/s (2096707 Bytes, 310482 us)S - DDR Frequency, 466 MHzS - Core 0 Frequency, 800 MHzU-Boot 2016.01 (Jul 10 2020 - 05:56:17 +0000), Build: jenkins-ra69_ota_publish-19DRAM: smem ram ptable found: ver: 1 len: 4512 MiBNAND: ONFI device foundID = 158061c8Vendor = c8Device = 61SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffffipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)128 MiBMMC: sdhci: Node Not found, skipping initialization## Error: flags type check failure for "ethaddr" <= ""00:AA:BB:CC:DD:10"" (type: m)himport_r: can't insert "ethaddr="00:AA:BB:CC:DD:10"" into hash tablePCI1 is not defined in the device treeIn: serial@78B3000Out: serial@78B3000Err: serial@78B3000machid: 8010010MMC Device 0 not foundeth5 MAC Address from ART is not validwrite phy_id=1, reg(0x8074):0x0670write phy_id=2, reg(0x8074):0x0670write phy_id=3, reg(0x8074):0x0670write phy_id=4, reg(0x8074):0x0670bootwait is off, bootdelay=5Hit any key to stop autoboot: 0 trigger button release!boot from rootfs 1 miwifi: check crash in rmem !ubi0: attaching mtd1ubi0: scanning is finishedubi0: attached mtd1 (name "mtd=0", size 35 MiB)ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytesubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096ubi0: good PEBs: 286, bad PEBs: 0, corrupted PEBs: 0ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 305386615ubi0: available PEBs: 40, total reserved PEBs: 246, PEBs reserved for bad PEB handling: 20Read 0 bytes from volume kernel to 44000000No size specified -> Using max size (4317184)Could not find PCI in device tree## Loading kernel from FIT Image at 44000000 ... Using 'config@ac04' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e8 Data Size: 3957925 Bytes = 3.8 MiB Architecture: AArch64 OS: Linux Load Address: 0x41080000 Entry Point: 0x41080000 Hash algo: crc32 Hash value: 2ce02202 Hash algo: sha1 Hash value: 3fe50e4ae8337afb7b96a86638221462ee455ad3 Verifying Hash Integrity ... crc32+ sha1+ OK## Loading fdt from FIT Image at 44000000 ... Using 'config@ac04' configuration Trying 'fdt@ac04' fdt subimage Description: ARM64 OpenWrt qcom-ipq807x-hkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x443da1c0 Data Size: 79565 Bytes = 77.7 KiB Architecture: AArch64 Hash algo: crc32 Hash value: b4ed9ff8 Hash algo: sha1 Hash value: 6119388eb1ae982f4a3586f267c7ea804db115bb Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x443da1c0 Uncompressing Kernel Image ... OK Loading Device Tree to 4a3e9000, end 4a3ff6cc ... OKUsing machid 0x8010010 from environmentStarting kernel ...Jumping to AARCH64 kernel via monitor[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Initializing cgroup subsys cpuset[ 0.000000] Initializing cgroup subsys cpu[ 0.000000] Initializing cgroup subsys cpuacct[ 0.000000] Linux version 4.4.60 (jenkins@92a4a83f0eca) (gcc version 5.5.0 (OpenWrt GCC 5.5.0 unknown) ) #0 SMP PREEMPT Tue Aug 18 13:50:52 2020[ 0.000000] Boot CPU: AArch64 Processor [410fd034][ 0.000000] Ignoring memory range 0x40000000 - 0x41000000[ 0.000000] efi: Getting EFI parameters from FDT:[ 0.000000] efi: UEFI not found.[ 0.000000] psci: probing for conduit method from DT.[ 0.000000] psci: PSCIv1.0 detected in firmware.[ 0.000000] psci: Using standard PSCI v0.2 function IDs[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.[ 0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc01ef5c000 s19096 r8192 d30056 u57344[ 0.000000] Detected VIPT I-cache on CPU0[ 0.000000] CPU features: enabling workaround for ARM erratum 845719[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 105840[ 0.000000] Kernel command line: ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1[ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes)[ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)[ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes)[ 0.000000] software IO TLB [mem 0x5fe57000-0x5fe97000] (0MB) mapped at [ffffffc01ee57000-ffffffc01ee96fff][ 0.000000] Memory: 402204K/430080K available (5491K kernel code, 654K rwdata, 2796K rodata, 224K init, 405K bss, 27876K reserved, 0K cma-reserved)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB)[ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum)[ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc0800000 ( 7 MB actual)[ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB)[ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB)[ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB)[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc01f000000 ( 496 MB)[ 0.000000] .init : 0xffffffc00089a000 - 0xffffffc0008d2000 ( 224 KB)[ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0008997f4 ( 8294 KB)[ 0.000000] .data : 0xffffffc0008e1000 - 0xffffffc000984800 ( 654 KB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1[ 0.000000] Preemptible hierarchical RCU implementation.[ 0.000000] Build-time adjustment of leaf fanout to 64.[ 0.000000] NR_IRQS:64 nr_irqs:64 0[ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns[ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns[ 0.000422] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)[ 0.000434] pid_max: default: 32768 minimum: 301[ 0.000522] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)[ 0.000532] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes)[ 0.001064] Initializing cgroup subsys io[ 0.001080] Initializing cgroup subsys memory[ 0.001110] Initializing cgroup subsys devices[ 0.001125] Initializing cgroup subsys freezer[ 0.001136] Initializing cgroup subsys net_cls[ 0.001146] Initializing cgroup subsys pids[ 0.001396] EFI services will not be available.[ 0.001421] ASID allocator initialised with 65536 entries[ 0.051840] MSM Memory Dump base table set up[ 0.051865] MSM Memory Dump apps data table set up[ 0.090113] Detected VIPT I-cache on CPU1[ 0.090156] CPU1: Booted secondary processor [410fd034][ 0.120099] Detected VIPT I-cache on CPU2[ 0.120127] CPU2: Booted secondary processor [410fd034][ 0.150127] Detected VIPT I-cache on CPU3[ 0.150154] CPU3: Booted secondary processor [410fd034][ 0.150206] Brought up 4 CPUs[ 0.150233] SMP: Total of 4 processors activated.[ 0.150242] CPU: All CPU(s) started at EL1[ 0.150266] alternatives: patching kernel code[ 0.167086] DMI not present or invalid.[ 0.167337] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.167362] futex hash table entries: 1024 (order: 5, 131072 bytes)[ 0.167585] pinctrl core: initialized pinctrl subsystem[ 0.168528] NET: Registered protocol family 16[ 0.190056] cpuidle: using governor ladder[ 0.220073] cpuidle: using governor menu[ 0.220217] vdso: 2 pages (1 code @ ffffffc0008e9000, 1 data @ ffffffc0008e8000)[ 0.220359] DMA: preallocated 256 KiB pool for atomic allocations[ 0.220453] CPU: unavail, SoC Version: 2.0[ 0.220489] <CORE> glink_init: IPC Logging Disabled[ 0.220888] IPC logging disabled[ 0.220894] IPC logging disabled[ 0.220899] IPC logging disabled[ 0.220904] IPC logging disabled[ 0.220908] IPC logging disabled[ 0.223617] Soc version is not 1, changing clock offsets[ 0.235006] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.237038] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ![ 0.239222] msm_rpm_dev_probe: APSS-RPM communication over GLINK[ 0.240154] sps:sps is ready.[ 0.249922] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 2[ 0.256446] pps_core: LinuxPPS API ver. 1 registered[ 0.256459] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>[ 0.256485] PTP clock support registered[ 0.256635] dmi: Firmware registration failed.[ 0.257962] Advanced Linux Sound Architecture Driver Initialized.[ 0.258605] clocksource: Switched to clocksource arch_sys_counter[ 0.261860] NET: Registered protocol family 2[ 0.262452] TCP established hash table entries: 4096 (order: 3, 32768 bytes)[ 0.262512] TCP bind hash table entries: 4096 (order: 4, 65536 bytes)[ 0.262609] TCP: Hash tables configured (established 4096 bind 4096)[ 0.262662] UDP hash table entries: 256 (order: 1, 8192 bytes)[ 0.262685] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)[ 0.262856] NET: Registered protocol family 1[ 0.270481] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.270498] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.273794] io scheduler noop registered[ 0.273810] io scheduler deadline registered (default)[ 0.275947] 20000000.pci supply vdda not found, using dummy regulator[ 0.276029] 20000000.pci supply vdda_phy not found, using dummy regulator[ 0.276064] 20000000.pci supply vdda_refclk not found, using dummy regulator[ 0.276611] PCI host bridge /soc/pci@20000000 ranges:[ 0.276638] IO 0x20200000..0x202fffff -> 0x20200000[ 0.276653] MEM 0x20300000..0x20ffffff -> 0x20300000[ 1.308651] qcom-pcie 20000000.pci: phy link never came up[ 1.310195] qcom-pcie 20000000.pci: hostinit failed[ 1.310205] qcom-pcie 20000000.pci: cannot initialize host[ 1.310353] qcom-pcie: probe of 20000000.pci failed with error -110[ 1.315797] NET: Registered protocol family 27[ 1.315810] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled[ 1.315823] qmi_log_init: IPC Logging disabled[ 1.315828] qmi_log_init: IPC Logging disabled[ 1.315919] msm_rpm_log_probe: OK[ 1.316498] msm-dcc b3000.dcc: DCC XPU is not specified[ 1.316741] msm-dcc b3000.dcc: DCC SRAM dump setup failed[ 1.316764] msm-dcc b3000.dcc: jiffies_64: 0xffff8b52, cntvct_64: 0xc1445f4[ 1.316776] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80003cc004)[ 1.316786] msm-dcc b3000.dcc: gcnt_lo: 0x0c1447a9(0xffffff80003cc000)[ 1.317332] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set[ 1.317998] msm_serial 78b3000.serial: msm_serial: detected port #0[ 1.318033] msm_serial 78b3000.serial: uartclk = 3686400[ 1.318066] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM[ 1.318084] msm_serial: console setup on port #0[ 2.053860] console [ttyMSM0] enabled[ 2.058822] msm_serial 78b1000.serial: msm_serial: detected port #1[ 2.062092] msm_serial 78b1000.serial: uartclk = 19200000[ 2.068163] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 78, base_baud = 1200000) is a MSM[ 2.074023] msm_serial: driver initialized[ 2.082505] msm_serial_hsl_init: driver initialized[ 2.095261] brd: module loaded[ 2.095944] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64[ 2.098723] m25p80 spi32766.0: unrecognized JEDEC id bytes: ff, ff, ff[ 2.105476] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0x61[ 2.110787] nand: GigaDevice PSR1GA30DT[ 2.117254] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 2.120937] 16 ofpart partitions found on MTD device qcom_nand.0[ 2.128455] Creating 16 MTD partitions on "qcom_nand.0":[ 2.134636] 0x000000000000-0x000000100000 : "0:SBL1"[ 2.141589] 0x000000100000-0x000000200000 : "0:MIBIB"[ 2.146387] 0x000000200000-0x000000500000 : "0:QSEE"[ 2.153161] 0x000000500000-0x000000580000 : "0:DEVCFG"[ 2.155908] 0x000000580000-0x000000600000 : "0:RPM"[ 2.160891] 0x000000600000-0x000000680000 : "0:CDT"[ 2.165642] 0x000000680000-0x000000700000 : "0:APPSBLENV"[ 2.170516] 0x000000700000-0x000000800000 : "0:APPSBL"[ 2.176498] 0x000000800000-0x000000880000 : "0:ART"[ 2.181144] 0x000000880000-0x000000900000 : "bdata"[ 2.185858] 0x000000900000-0x000000980000 : "crash"[ 2.190721] 0x000000980000-0x000000a00000 : "crash_syslog"[ 2.195563] 0x000000a00000-0x000002dc0000 : "rootfs"[ 2.232557] mtd: device 12 (rootfs) set to be root filesystem[ 2.232882] mtdsplit: no squashfs found in "rootfs"[ 2.237284] 0x000002dc0000-0x000005180000 : "rootfs_1"[ 2.274445] 0x000005180000-0x000007040000 : "overlay"[ 2.302197] 0x000007040000-0x0000070c0000 : "rsvd0"[ 2.303801] spmi spmi-0: PMIC Arb Version-2 (0x20010000)[ 2.308782] libphy: Fixed MDIO Bus: probed[ 2.532078] qca-mdio 90000.mdio: Could not find phy-reset-gpio[ 2.532187] libphy: qca_mdio: probed[ 2.538021] qca-mdio 90000.mdio: qca-mdio driver was registered[ 2.540749] Unable to create IPC log context![ 2.546468] cnss: Platform driver probed successfully.[ 2.550942] Skip QCA8074V1 in V2 platform[ 2.555821] cnss_genl: genl_register_family fail: -17[ 2.559845] cnss: CNSS genl init failed -17[ 2.564826] cnss: Platform driver probed successfully.[ 2.569006] i2c /dev entries driver[ 2.580550] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com[ 2.581003] sdhci: Secure Digital Host Controller Interface driver[ 2.588046] sdhci: Copyright(c) Pierre Ossman[ 2.594065] sdhci-pltfm: SDHCI platform and OF driver helper[ 2.599150] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed[ 2.604249] ICE IRQ = 81[ 2.612792][ 2.612792] Version Rollback Feature Disabled[ 2.615714] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000[ 2.620710] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000[ 2.637965] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000[ 2.653860] sps:BAM 0x0000000008b04000 is registered.[ 2.661603] DEV CI test message[ 2.666300] subsys-restart: ssr_parse_restart_orders(): q6v5_m3 device has been added to q6v5-m3's restart group[ 2.669066] subsys-restart: ssr_parse_restart_orders(): q6v5_wcss device has been added to q6v5-m3's restart group[ 2.679544] remoteproc remoteproc0: q6v5-m3 is available[ 2.689972] SPMI VADC - Min ch: 0 Max ch: 15[ 2.696751] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000[ 2.699437] coresight-csr 6001000.csr: CSR initialized[ 2.706858] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000[ 2.711834] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000[ 2.719371] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000[ 2.726733] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000[ 2.734128] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000[ 2.741516] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000[ 2.748885] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000[ 2.756247] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000[ 2.763643] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000[ 2.771025] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000[ 2.778387] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000[ 2.785783] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000[ 2.793155] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000[ 2.800539] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000[ 2.807905] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000[ 2.815291] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000[ 2.822672] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000[ 2.830213] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000[ 2.837535] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000[ 2.844964] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000[ 2.852378] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000[ 2.859756] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000[ 2.866787] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000[ 2.883896] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000[ 2.899782] sps:BAM 0x0000000006044000 is registered.[ 2.907407] coresight-tmc 6028000.tmc: TMC initialized[ 2.912217] coresight-tmc 6027000.tmc: TMC initialized[ 2.917346] coresight-funnel 6021000.funnel: FUNNEL initialized[ 2.922409] coresight-funnel 6100000.funnel: FUNNEL initialized[ 2.928206] coresight-funnel 6120000.funnel: FUNNEL initialized[ 2.934130] coresight-funnel 61a1000.funnel: FUNNEL initialized[ 2.940561] coresight-etm4x 619c000.etm: ETM 4.0 initialized[ 2.946242] coresight-etm4x 619d000.etm: ETM 4.0 initialized[ 2.952191] coresight-etm4x 619e000.etm: ETM 4.0 initialized[ 2.957853] coresight-etm4x 619f000.etm: ETM 4.0 initialized[ 2.963142] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized[ 2.968885] coresight-stm 6002000.stm: STM initialized[ 2.977408] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000[ 2.981313] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized[ 2.991680] Netfilter messages via NETLINK v0.30.[ 2.996511] ip_set: protocol 6[ 3.001789] NET: Registered protocol family 10[ 3.004814] NET: Registered protocol family 17[ 3.008485] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.[ 3.012936] Bridge firewalling registered[ 3.025647] 8021q: 802.1Q VLAN Support v1.8[ 3.031020] <CORE> glink_core_register_transport: IPC Logging disabled[ 3.033649] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 2[ 3.040160] msm_glink_smem_native_xprt rx fifo not found[ 3.047489] pmd9655_s3: supplied by e-smps1-reg[ 3.053103] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0[ 3.057146] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1[ 3.063760] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0[ 3.071409] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable[ 3.078911] cpr3_mem_acc_init: apc: not using memory accelerator regulator[ 3.088052] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV[ 3.095013] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 816000 uV[ 3.105038] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 698, quot_offset[ 7]= 0[ 3.114808] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 916, quot_offset[ 7]= 215[ 3.125752] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop[ 3.137858] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz[ 3.143468] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz[ 3.150734] DEV CI test message[ 3.159566] remoteproc remoteproc1: q6v5-wcss is available[ 3.162291] ubi0: attaching mtd13[ 3.351826] ubi0: scanning is finished[ 3.358530] ubi0: attached mtd13 (name "rootfs_1", size 35 MiB)[ 3.358550] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 3.363255] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 3.370197] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 3.377047] ubi0: good PEBs: 286, bad PEBs: 0, corrupted PEBs: 0[ 3.383823] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128[ 3.390076] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 305386615[ 3.397104] ubi0: available PEBs: 40, total reserved PEBs: 246, PEBs reserved for bad PEB handling: 20[ 3.406058] ubi0: background thread "ubi_bgt0d" started, PID 118[ 3.416145] hctosys: unable to open rtc device (rtc0)[ 3.446719] crash_kernel_init, res rsvd1, 50700000, 400000, /reserved-memory/rsvd1@50700000[ 3.446752] mtd dev crash, size 0x80000[ 3.454632] crash_kernel_init, crash init, res->start:50700000,crash_buf:0xffffff8001c80000,crash_buf_len 0x7ffe4, crash_avail_sz 0x80000[ 3.458308] Crash kernel dumper registered ok![ 3.471011] crash_syslog_init, res rsvd2, 50b00000, 400000, /reserved-memory/rsvd2@50b00000[ 3.475489] mtd dev crash_syslog, size 0x80000[ 3.484632] crash_syslog_init, crash init, crash_buf_len 0x3ffe4, crash_avail_sz 0x40000[ 3.488790] Crash syslog dumper register ok![ 3.497222] pmd9655_ldo11: disabling[ 3.501955] ALSA device list:[ 3.505163] No soundcards found.[ 3.510338] VFS: Mounted root (squashfs filesystem) readonly on device 31:17.[ 3.511471] Freeing unused kernel memory: 224K (ffffffc00089a000 - ffffffc0008d2000)[ 3.518560] Freeing alternatives memory: 44K (ffffffc0008d2000 - ffffffc0008dd000)[ 3.866556] init: Console is alive[ 3.866675] init: - watchdog -[ 3.988974] random: nonblocking pool is initialized[ 4.980890] kmodloader: loading kernel modules from /etc/modules-boot.d/*[ 4.996429] usbcore: registered new interface driver usbfs[ 4.996482] usbcore: registered new interface driver hub[ 5.000929] usbcore: registered new device driver usb[ 5.007658] Button Hotplug driver version 0.4.1[ 5.013720] SCSI subsystem initialized[ 5.017441] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver[ 5.019908] ehci-platform: EHCI generic platform driver[ 5.248565] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller[ 5.248655] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1[ 5.253093] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010[ 5.260537] xhci-hcd xhci-hcd.0.auto: irq 189, io mem 0x08a00000[ 5.269577] hub 1-0:1.0: USB hub found[ 5.275431] hub 1-0:1.0: 1 port detected[ 5.279183] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller[ 5.283062] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2[ 5.288397] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.[ 5.296238] hub 2-0:1.0: USB hub found[ 5.304262] hub 2-0:1.0: 1 port detected[ 5.310542] kmodloader: done loading kernel modules from /etc/modules-boot.d/*[ 5.319016] init: - preinit -Press the [f] key and hit [enter] to enter failsafe modePress the [1], [2], [3] or [4] key and hit [enter] to select the debug level[ 8.674408] mount_root: mounting /dev/root[ 8.725656] ubi1: attaching mtd14[ 8.885682] ubi1: scanning is finished[ 8.908221] ubi1: attached mtd14 (name "overlay", size 30 MiB)[ 8.908249] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 8.912958] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 8.919809] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096[ 8.926657] ubi1: good PEBs: 246, bad PEBs: 0, corrupted PEBs: 0[ 8.933433] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128[ 8.939687] ubi1: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 711819256[ 8.946714] ubi1: available PEBs: 0, total reserved PEBs: 246, PEBs reserved for bad PEB handling: 20[ 8.955675] ubi1: background thread "ubi_bgt1d" started, PID 189UBI device number 1, total 246 LEBs (31236096 bytes, 29.7 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB)u[ 8.979228] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 200bimkvol: error!: UBI device does not have free logical eraseblocks[ 9.015525] UBIFS (ubi1:0): recovery needed[ 9.123860] UBIFS (ubi1:0): recovery completed[ 9.123924] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "data"[ 9.127190] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 9.134415] UBIFS (ubi1:0): FS size: 26918912 bytes (25 MiB, 212 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs)[ 9.144390] UBIFS (ubi1:0): reserved for root: 1271446 bytes (1241 KiB)[ 9.154628] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID FB3689B6-15C2-4FD2-B89B-27D6C707D1AA, small LPT model2116+0 records in2116+0 records out2116 bytes (2.1KB) copied, 0.006090 seconds, 339.3KB/s131072+0 records in131072+0 records out131072 bytes (128.0KB) copied, 0.345192 [ 9.542534] urandom-seed: Seed file not found (/etc/urandom.seed)seconds, 370.8KB/s[ 10.062019] procd: - early -[ 10.062070] procd: - watchdog -[ 10.660570] procd: - watchdog -[ 10.660694] procd: - ubus -[ 10.712929] procd: - init -Please press Enter to activate this console./etc/rc.d/S00sysfixtime: Tue Dec 29 00:52:11 UTC 2020/etc/rc.d/S00wifi_fw_mount: 2116+0 records in/etc/rc.d/S00wifi_fw_mount: 2116+0 records out/etc/rc.d/S00wifi_fw_mount: 2116 bytes (2.1KB) copied, 0.006010 seconds, 343.8KB/s/etc/rc.d/S00wifi_fw_mount: 131072+0 records in/etc/rc.d/S00wifi_fw_mount: 131072+0 records out/etc/rc.d/S00wifi_fw_mount: 131072 bytes (128.0KB) copied, 0.342413 seconds, 373.8KB/s/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/mem failed: Resource busy/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/net_cls failed: Resource busy/etc/rc.d/S03cgroup_init: mount: mounting none on /dev/cgroup/cpu failed: Resource busy/etc/rc.d/S09qca-iot: sh: write error: Invalid argument/etc/rc.d/S09qca-iot: /etc/rc.common: line 154: can't create /sys/class/gpio/gpio/direction: nonexistent directory/etc/rc.d/S09qca-iot: /etc/rc.common: line 154: can't create /sys/class/gpio/gpio/value: nonexistent directory/etc/rc.d/S09qca-iot: /etc/rc.common: line 154: can't create /sys/class/gpio/gpio/value: nonexistent directory/usr/bin/iotd[305]: Started iot daemon[ 11.263160] kmodloader: loading kernel modules from /etc/modules.d/*[ 11.865874] nf_conntrack version 0.5.0 (3144 buckets, 40000 max)[ 11.865904] xqnss: extend init success![ 11.878400] cfg80211: World regulatory domain updated:[ 11.878426] cfg80211: DFS Master region: unset[ 11.882461] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)[ 11.887035] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)[ 11.896654] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)[ 11.904437] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)[ 11.913809] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)[ 11.921781] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)[ 11.931529] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)[ 11.940947] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)[ 11.949019] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)[ 12.047114] ssdk_switch_device_num_init[998]:INFO:ess-switch dts node number: 1[ 12.050846] ssdk_dt_get_switch_node[836]:INFO:ess-switch DT exist![ 12.057729] ssdk_dt_parse_access_mode[737]:INFO:switch_access_mode: local bus[ 12.063889] ssdk_dt_parse_access_mode[750]:INFO:switchreg_base_addr: 0x3a000000[ 12.071012] ssdk_dt_parse_access_mode[751]:INFO:switchreg_size: 0x1000000[ 12.078299] ssdk_dt_parse_mac_mode[242]:INFO:mac mode = 0x0[ 12.084720] ssdk_dt_parse_mac_mode[251]:INFO:mac mode1 = 0xff[ 12.090281] ssdk_dt_parse_mac_mode[260]:INFO:mac mode2 = 0xff[ 12.096032] ssdk_dt_parse_uniphy[279]:INFO:ess-uniphy DT exist![ 12.101865] ssdk_dt_parse_intf_mac[683]:INFO:dp1 MAC 9c:9d:7e:55:18:a5[ 12.107661] ssdk_dt_parse_intf_mac[683]:INFO:dp2 MAC 28:d1:27:f7:b7:c4[ 12.114171] ssdk_dt_parse_intf_mac[683]:INFO:dp3 MAC 9c:9d:7e:55:18:a5[ 12.120688] ssdk_dt_parse_intf_mac[683]:INFO:dp4 MAC 9c:9d:7e:55:18:a5[ 12.127191] ssdk_dt_parse_intf_mac[683]:INFO:dp5 MAC 9c:9d:7e:55:18:a5[ 12.133721] ssdk_plat_init start[ 12.210708] ssdk_ppe_clock_init[464]:INFO:ppe and uniphy clock init successfully![ 12.213873] ssdk_probe[1884]:INFO:ess_rst doesn't exist![ 12.221794] HPPE initializing...[ 12.222443] malibu_phy_api_ops_init[2851]:INFO:qca probe malibu phy driver succeeded![ 12.233529] regi_init[3411]:INFO:Initializing HPPE!![ 12.448603] ssdk_ppe_reset_init[738]:INFO:ppe reset successfully![ 12.455797] qca_hppe_tdm_hw_init[737]:INFO:tdm setup num=96[ 12.459068] qca_hppe_portctrl_hw_init[165]:INFO:Hawkeye PPE port initializing[ 12.674716] ssdk_switch_register[1623]:INFO:Chip version 0x1500[ 12.677698] qca_link_polling_select[1285]:INFO:link-polling-required node does not exist[ 12.683936] ssdk_switch_register[1648]:INFO:polling is selected[ 12.691666] regi_init[3415]:INFO:Initializing HPPE Done!![ 12.696586] regi_init[3459]:INFO:qca-ssdk module init succeeded![ 12.704143] tun: Universal TUN/TAP device driver, 1.6[ 12.705033] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>[ 12.713220] EDMA ver 1 hw init[ 12.716277] EDMA HW Reset completed succesfully[ 12.719188] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)[ 12.723524] RxDesc:1 (15-15) RxFill:1 (7-7)[ 12.735363] **********************************************************[ 12.735391] * NSS Data Plane driver[ 12.740896] **********************************************************[ 12.748127] l2tp_core: L2TP core driver, V2.0[ 12.751571] l2tp_netlink: L2TP netlink interface[ 12.909993] nss_driver - fw of size 667888 bytes copied to load addr: 40000000, nss_id : 0[ 12.911755] Supported Frequencies -[ 12.917139] 187.2 MHz 748.8 MHz[ 12.923122] 1.4976 GHz [ 12.924080][ 12.926546] ffffffbffc62c680: meminfo init succeed[ 12.975794] node size 2 # items 4[ 12.975819] memory: 40000000 536870912 (avl 435597312) items 4 active_cores 2[ 12.978097] ffffffbffc62c680: nss core 0 booted successfully[ 12.983131] nss_driver - fw of size 265296 bytes copied to load addr: 40800000, nss_id : 1[ 12.984039] Supported Frequencies -[ 12.984040] 187.2 MHz[ 12.984040] 748.8 MHz[ 12.984041] 1.4976 GHz[ 12.984042][ 12.984218] ffffffbffc633780: meminfo init succeed[ 13.011898] node size 2 # items 4[ 13.016014] memory: 40000000 536870912 (avl 435621888) items 4 active_cores 2[ 13.019423] ffffffbffc633780: nss core 1 booted successfully[ 13.027991] sit: IPv6 over IPv4 tunneling driver[ 13.034626] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.[ 13.037578] gre: GRE over IPv4 demultiplexor driver[ 13.045390] ip_gre: GRE over IPv4 tunneling driver[ 13.050831] ip6_gre: GRE over IPv6 tunneling driver[ 13.056786] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)[ 13.062120] QCA multicast snooping installed successfully[ 13.068273] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 15.041276] QCA Hy-Fi multicast installation successfully[ 15.799159] nss_lag_init[354]:LAG Manager Installed[ 16.430265] PPP generic driver version 2.4.2[ 16.430922] NET: Registered protocol family 24[ 16.800032] <NSS-CRYPTO>:module loaded Build_ID - 08/19/20, 03:00:01 SoC=ipq807x_64[ 17.040489] cannot find nss-macsec0 node[ 17.040545] cannot find nss-macsec1 node[ 17.043494] cannot find nss-macsec2 node[ 17.047373] nss_macsec init success[ 17.411889] diag: IPC Logging disabled[ 20.209254] u32 classifier[ 20.209275] input device check on[ 20.210844] Actions configured[ 20.619244] Mirror/redirect action on[ 25.659788] ipaccount: ifname [lo] event[5][ 25.659814] ipaccount: ifname [miireg] event[5][ 25.662770] ipaccount: ifname [eth0] event[5][ 25.667290] ipaccount: ifname [eth1] event[5][ 25.671829] ipaccount: ifname [eth2] event[5][ 25.676138] ipaccount: ifname [eth3] event[5][ 25.680485] ipaccount: ifname [eth4] event[5][ 25.684818] ipaccount: ifname [ip6tnl0] event[5][ 25.689167] ipaccount: ifname [sit0] event[5][ 25.693846] ipaccount: ifname [gre0] event[5][ 25.698098] ipaccount: ifname [gretap0] event[5][ 25.702450] ipaccount: ifname [ip6gre0] event[5][ 25.707128] ipaccount: ifname [bond0] event[5][ 25.711741] ipaccount: ifname [teql0] event[5][ 25.961054] fuse init (API version 7.23)[ 26.191976] ip_tables: (C) 2000-2006 Netfilter Core Team[ 26.194440] l2tp_ppp: PPPoL2TP kernel driver, V2.0[ 26.463420] PPP MPPE Compression module registered[ 26.464452] PPTP driver version 0.8.5[ 26.471242] ipt: xt_cgroup_MARK installed ok.[ 26.482113] xt_time: kernel timezone is -0000[ 26.491664] kmodloader: done loading kernel modules from /etc/modules.d/*/etc/rc.d/S10boot: cp: omitting directory '/cfg/default/internal'/etc/rc.d/S10boot: cat: can't open '/lib/wifi/wifi_nss_hk_olnum': No such file or d[ 29.770358] configuring additional NSS pbufsirectory/etc/rc.d/S10boot: sh: 3: unknown operand[ 29.782802] additional pbufs of size 3100672 got added to NSS[ 29.796130] mem_manager: module license 'unspecified' taints kernel.[ 29.796158] Disabling lock debugging due to kernel taint[ 29.802480] __mm_init_module[ 29.826227] qdf_dbg_mask value is invalid[ 29.826250] Using the default module debug levels instead[ 29.829259] qdf_print_ctrl_register: Allocated print control object 0[ 29.834654] MINIDUMP VA .bss start=ffffffbffcd28f00 module=qdf[ 30.293876] wlan: [1394:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50[ 30.293969] MINIDUMP VA .bss start=ffffffbffcfb8a80 module=umacINFO: Cold boot calibration not applicable: ap-ac04[ 30.459108][ 30.459108] MINIDUMP VA .bss start=ffffffbffd244900 module=qca_ol=======ol_if_register_wifi3_0==========[ 30.471651] wlan: [1406:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd3788b8[ 30.474293] remoteproc remoteproc0: powering up q6v5-m3[ 30.502548] remoteproc remoteproc0: Booting fw image IPQ8074/m3_fw.mdt, size 284[ 30.502581] Sanity check passed for M3 image[ 30.555945] remoteproc remoteproc0: remote processor q6v5-m3 is now up[ 30.556137] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done[ 30.561389] wlan: [1406:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 2[ 30.566842] remoteproc remoteproc1: powering up q6v5-wcss[ 30.574319] remoteproc remoteproc1: Booting fw image IPQ8074/q6_fw.mdt, size 668[ 30.579823] Sanity check passed for the image[ 31.679051] glink_core_link_up glink is up[ 31.679240] glink_xprt_open_event[ 31.679378] Subsystem error monitoring/handling services are up[ 31.679415] remoteproc remoteproc1: remote processor q6v5-wcss is now up[ 31.679440] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled[ 31.679561] wlan: [1406:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 3[ 31.705085] cnss: QMI WLFW service connected, state: 0x1[ 31.705264] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc916248[ 31.717190] cnss: device_id : 0xfffe mem mode : [1][ 31.726763] cnss: Boardid from dts:292,FW:ff[ 31.737223] cnss: BDF location : 0x000000004b0c0000[ 31.737252] cnss: BDF IPQ8074/bdwlan.b292 size 131072[ 31.741294] cnss: BDF download response , result: 0, err: 0x0[ 31.746472] cnss: per device BDF location : 0x000000004b0e0000[ 31.751979] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000[ 31.759686] cnss: BDF download response , result: 0, err: 0x0[ 31.780196] wlan: [1406:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode[ 31.788794] wlan: [1406:I:ANY] qca_napi_create: 357: qca_napi_create: napi instance 0 created on pipe 4[ 31.789088] wlan: [1406:I:ANY] __ol_ath_attach: 3064: Allocated soc ffffffc018280880[ 31.797198] btcoex_support 0 wlan_prio_gpio 0[ 31.805171] wlan: [1406:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000[ 31.809379] wlan: [1406:E:CONFIG] cfg_uint_item_handler: 171: dp_rxdma_monitor_desc_ring=128 - Out of range [4096, 16384]; Using 4096[ 31.821057] wlan: [1406:I:ANY] osif_nss_wifi_soc_setup: 186: nss-wifili:#1 register wifili function for soc[ 31.832840] wlan: [1406:I:ANY] osif_nss_wifi_soc_setup: 198: nss register id -1 nss config 3 Target Type 18[ 31.842730] wlan: [1406:I:ANY] __ol_ath_attach: 3278: dev name soc0[ 31.852690] wlan: [1406:I:ANY] ol_ath_soc_attach: 6558: WMI attached. wmi_handle ffffffc01bf5d000[ 31.858562] wlan: [1406:I:ANY] htc_wmi_init: 5925: htc_wmi_init() HT Create . ffffffc0180e5000[ 31.867528] wlan: [1406:I:ANY] htc_wmi_init: 5932: htc_wmi_init() Skipping BMI Done.[ 31.876219] wlan: [1406:I:ANY] htc_wmi_init: 5989: [htc_wmi_init:5989] host_enable 0 nss_nwifi_offload 0[ 31.887949] wlan: [1406:I:ANY] ol_target_init_complete: 6107: CDP soc attach success[ 31.893555] wlan: [1406:I:ANY] ol_target_init_complete: 6114: Soc attach success NSS config 0[ 31.901373] wlan: [1406:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc0180e5000, ep 2, value 1[ 31.909880] wlan: [1406:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc0180e5000, ep 3, value 1[ 31.920586] wlan: [1138:I:TIF] HE_CAP Info = 1a08010d[ 31.930385] wlan: [1138:I:TIF] Num HW modes = 1[ 31.935450] wlan: [1138:I:TIF] Num PHY = 2[ 31.939800] wlan: [1138:I:TIF] Preferred HW Mode = 1 Num Radios = 2[ 31.943970] wlan: [1138:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,[ 31.950174] wlan: [1138:I:TIF] init_deinit_add_11ax_modes: 1406: phy_id = 0 wireless modes = f97f9001[ 31.958898] wlan: [1138:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,[ 31.968106] wlan: [1138:I:TIF] init_deinit_add_11ax_modes: 1406: phy_id = 1 wireless modes = 680680c[ 31.977036] wlan: [1138:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 390: dfs_offload 1[ 31.985997] wlan: [1138:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1038: dfs->dfs_psoc_idx: 0[ 31.996245] wlan: [1138:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1044: dfs_soc_obj->num_dfs_privs: 1[ 32.006000] wlan: [1138:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 362: Do not allocate DFS object for 2G, pdev_id = 1[ 32.023624] wlan: [1138:I:TIF] init_deinit_update_pdev_tgt_info: 1064: CDP PDEV ATTACH success[ 32.031371] wlan: [1138:I:TIF] init_deinit_update_pdev_tgt_info: 1064: CDP PDEV ATTACH success[ 32.138399] wlan: [1138:I:ANY] copy_fw_abi_version_tlv: 6258: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0[ 32.268701] wlan: [1138:I:ANY] dp_peer_map_attach_wifi3: 9979: dp_peer_map_attach_wifi3 max_peers 311, max_ast_index: 1040[ 32.268701][ 32.268816] wlan: [1138:I:ANY] ready_extract_init_status_tlv: 8002: ready_extract_init_status_tlv:0[ 32.280109] wlan: [1406:I:ANY] ol_ath_connect_htc: 1219: WMI is ready[ 32.342637] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 37 is unavailable[ 32.342862] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 141 is unavailable[ 32.350361] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 137 is unavailable[ 32.358836] wlan: [1406:I:ANY] ol_ath_soc_attach: 6632: connect HTC[ 32.368090] wlan: [1406:I:ANY] ol_ath_soc_attach: 6633: bypasswmi : 0[ 32.373589] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 38 is unavailable[ 32.380177] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 138 is unavailable[ 32.388702] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 139 is unavailable[ 32.397200] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 55 is unavailable[ 32.405788] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 49 is unavailable[ 32.414392] wlan: [1406:E:WMI] wmi_unified_register_event_handler: Event id 25 is unavailable[ 32.422886] wlan: [1406:I:ANY] ol_ath_soc_attach: 6708: ol_ath_soc_attach() UMAC attach .[ 32.431401] *skip LOWI socket init, save id22 for ALD*[ 32.439791] wlan: [1406:I:ANY] __ol_ath_attach: 3397: pdev_netdev name wifi0[ 32.445034] wlan: [1406:I:ANY] __ol_ath_attach: 3442: Skip txrx_pdev_attach_target[ 32.452144] wlan: [1406:I:ANY] __ol_ath_attach: 3466: BURSTING enabled by default[ 32.459794] wlan: [1406:I:ANY] ol_ath_pdev_attach: 7173: interface_id 0[ 32.467092] wlan: [1406:I:ANY] ol_ath_pdev_regdmn_init: 6862: phy id = 0 Modes supported[ 32.473503] wlan: [1406:I:ANY] ol_ath_pdev_regdmn_init: 6869: 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1[ 32.482039] wlan: [1406:I:ANY] ol_ath_pdev_regdmn_init: 6877: Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4910, hi_5g = 6100[ 32.492272] wlan: [1406:I:ANY] ol_ath_update_wireless_modes: 1318: wireless_modes = f97f9001 before update[ 32.506611] wlan: [1406:I:ANY] ol_ath_update_wireless_modes: 1333: Wireless_modes = f97f9001 after update[ 32.516153] wlan: [1406:I:ANY] ol_ath_update_ext_caps: 1844: 11ax 5G supported case[ 32.526760] wlan: [1406:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed[ 32.533300] ieee80211_cbs_init CBS Inited[ 32.543106] wlan: [1406:I:ANY] acfg_attach: 3457: acfg_attach: 3457: Netlink socket created:ffffffc0170df000[ 32.543812] wlan: [1406:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX[ 32.554088] wlan: [1406:I:ANY] ol_ath_stats_attach: 2071: periodic_chan_stats: 1[ 32.567395] wlan: [1406:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 25[ 32.571324] wlan: [0:I:ANY] ol_ath_pdev_attach: 7509: Set global_ic[1], ptr:ffffffbffcfb8de0[ 32.578645] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc018274888) Enabling DBDC Repeater 1[ 32.587148] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed[ 32.595823] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc018274888) is_primary 1[ 32.604157] wlan: [1406:I:ANY] ol_ath_pdev_attach: 7626: Pdev = 0 Number of peers = 137[ 32.613243] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 11867: twt enabled.[ 32.613243][ 32.615478] wlan: [1406:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 1) chan 36 blocked from cfg[ 32.615483] wlan: [1406:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 2) chan 132 blocked from cfg[ 32.615511] wlan: [1406:I:ANY] osif_wrap_attach: 239: osif wrap attached[ 32.615511][ 32.615515] wlan: [1406:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done[ 32.615515][ 32.615522] wlan: [1406:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc018523400 ic->ic_wrap_com=ffffffc018523400 &wrap_com->wc_devt=ffffffc018523400[ 32.615522][ 32.615547] wlan: [1406:I:ANY] __ol_ath_attach: 3646: needed_headroom reservation 60[ 32.615553] wlan: [1406:I:ANY] ol_ath_enable_fraglist: 2931: Enabled Fraglist bit for the radio wifi0 features 41[ 32.615616] wlan: [1406:I:ANY] wlan_cfg80211_init: 9619: Number of 5G channels: 25[ 32.615856] wlan: [1406:I:ANY] ieee80211_cfg80211_radio_attach: 9713: ic: 0xffffffc016940880, wdev: 0xffffffc016950a70, wiphy: 0xffffffc01702a2a0, netdev: 0xffffffc016940000[ 32.615921] ipaccount: ifname [wifi0] event[16][ 32.616328] ipaccount: ifname [wifi0] event[5][ 32.616431] wlan: [1406:I:ANY] __ol_ath_attach: 3397: pdev_netdev name wifi1[ 32.616450] wlan: [1406:I:ANY] __ol_ath_attach: 3442: Skip txrx_pdev_attach_target[ 32.616454] wlan: [1406:I:ANY] __ol_ath_attach: 3466: BURSTING enabled by default[ 32.616500] wlan: [1406:I:ANY] ol_ath_pdev_attach: 7173: interface_id 1[ 32.616511] wlan: [1406:I:ANY] ol_ath_pdev_regdmn_init: 6862: phy id = 1 Modes supported[ 32.616517] wlan: [1406:I:ANY] ol_ath_pdev_regdmn_init: 6869: 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1[ 32.616523] wlan: [1406:I:ANY] ol_ath_pdev_regdmn_init: 6877: Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0[ 32.616527] wlan: [1406:I:ANY] ol_ath_update_wireless_modes: 1318: wireless_modes = 680680c before update[ 32.616531] wlan: [1406:I:ANY] ol_ath_update_wireless_modes: 1333: Wireless_modes = 680680c after update[ 32.616535] wlan: [1406:I:ANY] ol_ath_update_ext_caps: 1852: 11ax 2G supported case[ 32.616646] wlan: [1406:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed[ 32.616717] ieee80211_cbs_init CBS Inited[ 32.616731] wlan: [1406:I:ANY] acfg_attach: 3432: Offload using existing sock ffffffc0170df000[ 32.616741] wlan: [1406:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX[ 32.616746] wlan: [1406:I:ANY] ol_ath_stats_attach: 2071: periodic_chan_stats: 1[ 32.616962] wlan: [1406:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 11[ 32.616983] wlan: [0:I:ANY] ol_ath_pdev_attach: 7509: Set global_ic[2], ptr:ffffffbffcfb8de0[ 32.616989] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc016383288) Enabling DBDC Repeater 1[ 32.617010] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc016383288) is_primary 0[ 32.617020] wlan: [1406:I:ANY] ol_ath_pdev_attach: 7626: Pdev = 1 Number of peers = 137[ 32.618361] wlan: [1406:E:WMI] event handler already registered 0x6019[ 32.619289] wlan: [1406:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 1) chan 36 blocked from cfg[ 32.619294] wlan: [1406:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 2) chan 132 blocked from cfg[ 32.619314] wlan: [1406:I:ANY] osif_wrap_attach: 239: osif wrap attached[ 32.619314][ 32.619318] wlan: [1406:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done[ 32.619318][ 32.619324] wlan: [1406:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc01257cc00 ic->ic_wrap_com=ffffffc01257cc00 &wrap_com->wc_devt=ffffffc01257cc00[ 32.619324][ 32.619341] wlan: [1406:I:ANY] __ol_ath_attach: 3646: needed_headroom reservation 60[ 32.619346] wlan: [1406:I:ANY] ol_ath_enable_fraglist: 2931: Enabled Fraglist bit for the radio wifi1 features 41[ 32.619362] wlan: [1406:I:ANY] wlan_cfg80211_init: 9607: Number of 2G channels: 11[ 32.619502] wlan: [1406:I:ANY] ieee80211_cfg80211_radio_attach: 9713: ic: 0xffffffc016980880, wdev: 0xffffffc016990a70, wiphy: 0xffffffc01702d2a0, netdev: 0xffffffc016980000[ 32.619527] ipaccount: ifname [wifi1] event[16][ 32.619889] ipaccount: ifname [wifi1] event[5][ 32.619970] ipaccount: ifname [soc0] event[16][ 32.620204] ipaccount: ifname [soc0] event[5][ 32.620237] wlan: [1406:I:ANY] wlan_pdev_operation: 729: num_radios=1, wifi_radios[0].sc = ffffffc016940880_radio_type = 2[ 32.620243] wlan: [1406:I:ANY] wlan_pdev_operation: 729: num_radios=2, wifi_radios[1].sc = ffffffc016980880_radio_type = 2[ 32.620271] wlan: [1406:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0: (Atheros/multi-bss)[ 33.040948][ 33.040948] MINIDUMP VA .bss start=ffffffbffd378d00 module=wifi_3_0[ 33.040949] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed[ 33.057856] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 11867: twt enabled.[ 33.057856][ 33.081847] wlan: [1411:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd441858[ 33.081893] wlan: [1411:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd441858[ 33.093631] wlan: [1411:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi-bss)No Direct-Attach chipsets found./etc/rc.d/S10boot: cat: can't open '1': No such file or directory/etc/rc.d/S10boot: killall: acfg_tool: no process killed/etc/rc.d/S10boot: /sbin/wifi: eval: line 1: /usr/sbin/acfg_tool: not found[ 33.986139] ipaccount: ifname [bond0] event[11]/etc/rc.d/S15qca-wpa-supplicant: Successfully initialized wpa_supplicant/etc/rc.d/S16qca-ssdk:/etc/rc.d/S16qca-ssdk: starting/etc/rc.d/S19dnsmasq: cp: can't stat '/etc/dnsmasq.d/*': No such file or directory/etc/rc.d/S19dnsmasq: sh: out of range/etc/rc.d/S19dnsmasq: sh: out of range/etc/rc.d/S19firewall: /etc/rc.common: line 1: /usr/sbin/firewall.webinitrdr: not found[ 36.642469] ECM init[ 36.642525] ECM database jhash random seed: 0x972d4bfa[ 36.644836] qcaecm: register ecm_nss_ipv4_post_routing_hook()[ 36.648905] ECM init complete/etc/rc.d/S19qca-nss-ecm: net.bridge.bridge-nf-call-ip6tables = 1/etc/rc.d/S19qca-nss-ecm: net.bridge.bridge-nf-call-iptables = 1/etc/rc.d/S19qca-nss-ecm: dev.nss.general.redirect = 1/etc/rc.d/S20network: uci: Invalid argument/etc/rc.d/S21nginx: start fcgi-cgi by spawn-fcgi./etc/rc.d/S21nginx: start nginx ok.lbd: stopping daemon/etc/init.d/network: Command failed: Not found[ 40.351217] ipaccount: ifname [br-lan] event[16][ 40.352169] ipaccount: ifname [br-lan] event[5][ 40.355695] ipaccount: ifname [eth2] event[13][ 40.369225] ipaccount: ifname [eth2] event[1][ 40.370196] ipaccount: ifname [eth2] event[20][ 40.372766] ipaccount: ifname [eth2] event[26][ 40.377211] ipaccount: ifname [eth2] event[21][ 40.381571] ipaccount: ifname [eth2] event[11][ 40.385762] device eth2 entered promiscuous mode[ 40.390635] ipaccount: ifname [br-lan] event[11][ 40.395272] ipaccount: ifname [br-lan] event[8][ 40.399825] ipaccount: ifname [eth2] event[27][ 40.404560] ipaccount: ifname [br-lan] event[8][ 40.408515] ipaccount: ifname [br-lan] event[13][ 40.413741] br-lan: port 1(eth2) entered forwarding state[ 40.417683] br-lan: port 1(eth2) entered forwarding state[ 40.423698] ipaccount: ifname [br-lan] event[1][ 40.433393] ipaccount: ifname [eth3] event[13][ 40.435614] ipaccount: ifname [eth3] event[1][ 40.438041] ipaccount: ifname [eth3] event[20][ 40.441904] ipaccount: ifname [eth3] event[26][ 40.446572] ipaccount: ifname [eth3] event[21][ 40.451328] ipaccount: ifname [eth3] event[11][ 40.458716] device eth3 entered promiscuous mode[ 40.459361] br-lan: port 2(eth3) entered forwarding state[ 40.464041] br-lan: port 2(eth3) entered forwarding state[ 40.470039] ipaccount: ifname [eth3] event[27][ 40.477333] ipaccount: ifname [eth4] event[13][ 40.481622] ipaccount: ifname [eth4] event[1][ 40.484460] ipaccount: ifname [eth4] event[20][ 40.488198] ipaccount: ifname [eth4] event[26][ 40.492831] ipaccount: ifname [eth4] event[21][ 40.496844] ipaccount: ifname [eth4] event[11][ 40.501254] device eth4 entered promiscuous mode[ 40.505665] br-lan: port 3(eth4) entered forwarding state[ 40.510342] br-lan: port 3(eth4) entered forwarding state[ 40.515836] ipaccount: ifname [eth4] event[27]/etc/init.d/network: Command failed: Not found/etc/init.d/network: killall: iface-mgr: no process killed[ 40.571549] ipaccount: ifname [eth1] event[13][ 40.572246] ipaccount: ifname [eth1] event[1][ 40.575860] ipaccount: ifname [lo] event[13][ 40.580191] ipaccount: ifname [lo] event[1]/etc/init.d/network: killall: acfg_tool: no process killed/etc/init.d/network: /sbin/wifi: eval: line 1: /usr/sbin/acfg_tool: not foundqcawificfg80211 disable radio wifi0[ 40.607434] hyfi_netlink_receive:114:hyfi: Not attached to bridge br-lanqcawificfg80211 disable radio wifi1/etc/rc.d/S49messagingagent.sh: start messagingagent ok./etc/rc.d/S50acd: acd *** not in cap/re mode, skip handlecrond[3365]: crond (busybox 1.25.1) started, log level 5/etc/init.d/network: device: wifi0 vifs: cfg023579/etc/init.d/network: device: wifi1 vifs: cfg043579 miot_2G/etc/init.d/network: killall: acfg_tool: no process killed/etc/init.d/network: /sbin/wifi: eval: line 1: /usr/sbin/acfg_tool: not foundqcawificfg80211: enable radio wifi0/etc/init.d/network: cp: omitting directory '/cfg/default/internal'/etc/rc.d/S51cp_preinstall_plugins.sh: ls: /usr/share/datacenter/appdata/notuninstallable/app_infos: No such file or directory/etc/rc.d/S51cp_preinstall_plugins.sh: ls: /usr/share/datacenter/appdata/uninstallable/app_infos: No such file or directory[ 41.348818] br-lan: port 1(eth2) entered disabled state[ 41.348949] ipaccount: ifname [eth2] event[4][ 41.352986] ipaccount: ifname [br-lan] event[4][ 41.357429] br-lan: port 2(eth3) entered disabled state[ 41.361777] ipaccount: ifname [eth3] event[4][ 41.367784] br-lan: port 3(eth4) entered disabled state[ 41.371999] ipaccount: ifname [eth4] event[4][ 41.377153] ipaccount: ifname [eth1] event[4]/etc/init.d/network: Enable ol_stats by default for Lithium platforms[ 42.113784] wlan: [4576:I:ANY] wlan_cfg80211_set_hwaddr: 5439: wlan_cfg80211_set_hwaddr :9c:9d:7e:55:18:5b ret: 0[ 42.145010] wlan: [4590:I:ANY] ol_ath_set_config_param: 1493: set TXBF_SND_PERIOD: value 100 wmi_status 0[ 42.261094] wlan: [0:I:ANY] ol_ath_set_config_param: 2203: Disconnect_timeout value: 10[ 42.294200] wlan: [0:I:ANY] ol_ath_set_config_param: 2209: Reconfiguration_timeout value:60/etc/init.d/network: cat: can't open '/lib/wifi/wifi_nss_hk_olnum': No such file or directory/etc/init.d/network: sh: 3: unknown operand[ 42.348747] ipaccount: ifname [br-lan] event[4]number of vifs:[ 42.512428] ipaccount: ifname [wifi0] event[13][ 42.513122] ipaccount: ifname [wifi0] event[1]/etc/init.d/network: sh: wl2: unknown operand/etc/init.d/network: sh: wl13: unknown operandqcawificfg80211: enable radio wifi1/etc/init.d/network: cp: omitting directory '/cfg/default/internal'/etc/rc.d/S51key_services_boot_check: @@@@@@ RA69 key_service_check skip wireless!/etc/init.d/network: Enable ol_stats by default for Lithium platforms[ 43.376151] wlan: [5560:I:ANY] wlan_cfg80211_set_hwaddr: 5439: wlan_cfg80211_set_hwaddr :9c:9d:7e:55:18:a5 ret: 0[ 43.404267] wlan: [5562:I:ANY] ol_ath_set_config_param: 1493: set TXBF_SND_PERIOD: value 100 wmi_status 0[ 43.493014] wlan: [0:I:ANY] ol_ath_set_config_param: 2203: Disconnect_timeout value: 10[ 43.523392] wlan: [0:I:ANY] ol_ath_set_config_param: 2209: Reconfiguration_timeout value:60/etc/init.d/network: cat: can't open '/lib/wifi/wifi_nss_hk_olnum': No such file or directory/etc/init.d/network: sh: 3: unknown operandnumber of vifs:[ 43.695206] ipaccount: ifname [wifi1] event[13][ 43.695415] ipaccount: ifname [wifi1] event[1]/etc/init.d/network: sh: wl2: unknown operand/etc/init.d/network: sh: wl13: unknown operand/etc/init.d/network: /sbin/wifi: eval: line 1: iface_mgr_setup: not found/etc/init.d/network: device: wifi0 vifs: cfg023579/etc/init.d/network: device: wifi1 vifs: cfg043579 miot_2G/etc/rc.d/S54hyfi-bridging: hyfi-bridging *** not in cap/re mode, skip handle/etc/rc.d/S55hyd: hyd *** not in cap/re mode, skip handle/etc/rc.d/S60iweventd: iwevent-call start ok/etc/rc.d/S77trafficd: refresh ifname into ipaacount in [lan-dev 5g-wl 2.4g-wl wl-guest[ 48.853059] ipaccount: refresh dev ifname to [eth2 eth3 eth4 wl0 wl1 wl14 wl5][ 48.856951] ipaccount: landev_init_all() add dev [eth2] is_wireless: 0.[ 48.864276] ipaccount: landev_init_all() add dev [eth3] is_wireless: 0.[ 48.870857] ipaccount: landev_init_all() add dev [eth4] is_wireless: 0.[ 48.877430] ipaccount: landev_init_all() get dev [wl0] not found.[ 48.884088] ipaccount: landev_init_all() get dev [wl1] not found.[ 48.890297] ipaccount: landev_init_all() get dev [wl14] not found.[ 48.896353] ipaccount: landev_init_all() get dev [wl5] not found. 5g-wl-backhaul]/etc/rc.d/S77trafficd: eth2 eth3 eth4 wl0 wl1 wl14 wl5/etc/rc.d/S77trafficd: trafficd start ok/etc/rc.d/S80datacenter: chmod: /userdisk/data: Read-only file systemxqwhc_repacd: **ppid=1, cmd=</sbin/procd>/etc/rc.d/S97repacd: cat: can't open '/proc/0/cmdline': No such file or directoryxqwhc_repacd: *parent ppid 0, cmd=<>xqwhc_repacd: *** in non-mesh mode, skip repacd handlexqwhc_repacd: **ppid=1, cmd=</sbin/procd>/etc/init.d/repacd: cat: can't open '/proc/0/cmdline': No such file or directoryxqwhc_repacd: *parent ppid 0, cmd=<>xqwhc_repacd: *** in non-mesh mode, skip repacd handle/etc/rc.d/S98miqos: {/etc/rc.d/S98miqos: status=0/etc/rc.d/S98miqos: data=ok/etc/rc.d/S98miqos: }/etc/rc.d/S98xqwhc: xqwhc *** not in cap/re mode, skip handle/etc/rc.d/S98xqwhc: { "name": "xqwhc", "script": "\/etc\/rc.d\/S98xqwhc", "instances": { }, "triggers": [ ], "data": { } }/etc/rc.d/S99boot_check: : INFO: rcS timing 45.418749785s seconds.Tue Dec 29 08:52:51 CST 2020 boot_check[6670]: Booting up finished.

IPQ807x# versionU-Boot 2016.01 (Jul 10 2020 - 05:56:17 +0000)arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 5.2.0 998fe11+r49254) 5.2.0GNU ld (GNU Binutils) 2.24.0IPQ807x# help? - alias for 'help'aq_load_fw- LOAD aq-fw-binaryaq_phy_restart- Restart Aquantia phybase - print or set address offsetbdinfo - print Board Info structurebootm - boot application image from memorybootmiwifi- bootmiwifi from flash devicebootp - boot image via network using BOOTP/TFTP protocolbootz - boot Linux zImage image from memorybtnc - check reset button if pressed to 5s - if so ret 1btni - init gpios for buttonchpart - change active partitioncmp - memory comparecp - memory copycrc32 - checksum calculationdcache - enable or disable data cachedhcp - boot image via network using DHCP/TFTP protocoldm - Driver model low level accessecho - echo args to consoleenv - environment handling commandserase - erase FLASH memoryexectzt - execute TZTexit - exit scriptfalse - do nothing, unsuccessfullyfdt - flattened device tree utility commandsflash - flash part_name flash part_name load_addr file_sizeflasherase- flerase part_nameflinfo - print FLASH memory informationfuseipq - fuse QFPROM registers from memorygo - start application at address 'addr'help - print command description/usagei2c - I2C sub-systemicache - enable or disable instruction cacheimxtract- extract a part of a multi-imageipq_mdio- IPQ mdio utility commandsis_sec_boot_enabled- check secure boot fuse is enabled or notitest - return true/false on integer compareloop - infinite loop on address rangemd - memory displaymii - MII utility commandsmm - memory modify (auto-incrementing address)mmc - MMC sub systemmmcinfo - display MMC infomtdparts- define flash/nand partitionsmtest - simple RAM read/write testmw - memory write (fill)nand - NAND sub-systemnboot - boot from NAND devicenm - memory modify (constant address)pci - list and access PCI Configuration Spaceping - send ICMP ECHO_REQUEST to network hostprintenv- print environment variablesprotect - enable or disable FLASH write protectionreset - Perform RESET of the CPUrmemcrash- miwifi check and save crash buff to mtdrun - run commands in an environment variablerunmulticore- Enable and schedule secondary coressaveenv - save environment variables to persistent storagesecure_authenticate- authenticate the signed imagesetenv - set environment variablessf - SPI flash sub-systemshowvar - print local hushshell variablessleep - delay execution for some timesmeminfo- print SMEM FLASH informationsource - run script from memorytest - minimal test like /bin/shtftpboot- boot image via network using TFTP protocoltftpput - TFTP put command, for uploading files to a servertrue - do nothing, successfullyuart - UART sub-systemubi - ubi commandsusb - USB sub-systemusbboot - boot from USB deviceversion - print monitor, compiler and linker versionxqup - load image and upgrade to flashIPQ807x# bdinfoarch_number = 0x08010010boot_params = 0x40000100DRAM bank = 0x00000000-> start = 0x40000000-> size = 0x20000000eth0name = eth0ethaddr = 9c:9d:7e:55:18:a5current eth = eth0ip_addr = 192.168.31.1baudrate = 115200 bpsTLB addr = 0x4A9A0000relocaddr = 0x4A900000reloc off = 0x00000000irq_sp = 0x4A7DFA90sp start = 0x4A7DFA80IPQ807x# baseBase Address: 0x00000000IPQ807x# printenvCountryCode=CNRouter_unconfigured=0SN=12345/A0U123456boot_wait=offbootargs=ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwaitbootcmd=bootmiwifibootdelay=5color=100eth1addr=28:d1:27:f7:b7:c4eth2addr=9c:9d:7e:55:18:a5eth3addr=9c:9d:7e:55:18:a5eth4addr=9c:9d:7e:55:18:a5ethact=eth0ethaddr=9c:9d:7e:55:18:a5fdt_high=0x4A400000fdtcontroladdr=4a979e90flag_boot_rootfs=1flag_boot_success=1flag_boot_type=2flag_flash_permission=1flag_last_success=1flag_ota_reboot=0flag_show_upgrade_info=1flag_try_sys1_failed=0flag_try_sys2_failed=0flash_type=2fsbootargs=ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfsipaddr=192.168.31.1machid=1234567miot_did=643138169miot_key=E8AXEyZTBeuoGyRymode=Routermodel=RA69mtddevname=fsmtddevnum=0mtdids=nand0=nand0mtdparts=mtdparts=nand0:0x23c0000@0x2dc0000(fs),no_wifi_dev_times=0nv_sys_pwd=c8197f570e4838b2783007428394ddb9de74cb1cnv_wan_type=dhcpnv_wifi_enc=mixed-psknv_wifi_enc1=mixed-psknv_wifi_pwd=test1234nv_wifi_pwd1=test1234nv_wifi_ssid=Redmi_4CB7nv_wifi_ssid1=Redmi_4CB7_5Gpartition=nand0,0restore_defaults=0serverip=192.168.31.100soc_version_major=2soc_version_minor=0ssh_en=1stderr=serial@78B3000stdin=serial@78B3000stdout=serial@78B3000telnet_en=0uart_en=1wl0_radio=1wl0_ssid=Redmi_5Gwl1_radio=1wl1_ssid=RedmiEnvironment size: 1449/65532 bytes

root@XiaoQiang:/# bootinfoROM ver: config core 'version' # ROM ver option ROM '1.0.18' # channel option CHANNEL 'release' # hardware platform R1AC or R1N etc. option HARDWARE 'RA69' # CFE ver option UBOOT '1.0.2' # Linux Kernel ver option LINUX '4.4.16' # RAMFS ver option RAMFS '0.0.1' # SQUASHFS ver option SQAFS '0.0.1' # ROOTFS ver option ROOTFS '0.0.1' #build time option BUILDTIME 'Wed, 19 Aug 2020 02:57:56 +0000' #build timestamp option BUILDTS '1597805876' #build git tag option GTAG 'commit 83f49d45da9a3e68cf4042d0f962ad66f751b14c'Hardware : Ver. AROM sum:System : Dual - 2KERNEL : ubi.mtd=rootfs_1 root=mtd:ubi_rootfs rootfstype=squashfs rootwait uart_en=1 swiotlb=1MTD table:dev: size erasesize namemtd0: 00100000 00020000 "0:SBL1"mtd1: 00100000 00020000 "0:MIBIB"mtd2: 00300000 00020000 "0:QSEE"mtd3: 00080000 00020000 "0:DEVCFG"mtd4: 00080000 00020000 "0:RPM"mtd5: 00080000 00020000 "0:CDT"mtd6: 00080000 00020000 "0:APPSBLENV"mtd7: 00100000 00020000 "0:APPSBL"mtd8: 00080000 00020000 "0:ART"mtd9: 00080000 00020000 "bdata"mtd10: 00080000 00020000 "crash"mtd11: 00080000 00020000 "crash_syslog"mtd12: 023c0000 00020000 "rootfs"mtd13: 023c0000 00020000 "rootfs_1"mtd14: 01ec0000 00020000 "overlay"mtd15: 00080000 00020000 "rsvd0"mtd16: 0041e000 0001f000 "kernel"mtd17: 016c4000 0001f000 "ubi_rootfs"mtd18: 01ae2000 0001f000 "data"IPQ807x# smeminfoflash_type: 0x2flash_index: 0x0flash_chip_select: 0x0flash_block_size: 0x20000flash_density: 0x100000partition table offset 0x0No.: Name Attributes Start Size 0: 0:SBL1 0x0000ffff 0x0 0x100000 1: 0:MIBIB 0x0000ffff 0x100000 0x100000 2: 0:QSEE 0x0000ffff 0x200000 0x300000 3: 0:DEVCFG 0x0000ffff 0x500000 0x80000 4: 0:RPM 0x0000ffff 0x580000 0x80000 5: 0:CDT 0x0000ffff 0x600000 0x80000 6: 0:APPSBLENV 0x0000ffff 0x680000 0x80000 7: 0:APPSBL 0x0000ffff 0x700000 0x100000 8: 0:ART 0x0000ffff 0x800000 0x80000 9: bdata 0x0000ffff 0x880000 0x80000 10: crash 0x0000ffff 0x900000 0x80000 11: crash_syslog 0x0000ffff 0x980000 0x80000 12: rootfs 0x0000ffff 0xa00000 0x23c0000 13: rootfs_1 0x0000ffff 0x2dc0000 0x23c0000 14: overlay 0x0000ffff 0x5180000 0x1ec0000 15: rsvd0 0x0000ffff 0x7040000 0x80000
root@XiaoQiang:/# cat /proc/interrupts CPU0 CPU1 CPU2 CPU3 3: 3216 2476 4398 2446 GIC 20 Edge arch_timer 40: 1 0 0 0 msmgpio 34 Edge soc:gpio_keys 76: 0 0 0 0 GIC 270 Level bam_dma 77: 229 0 0 0 GIC 340 Level msm_serial0 79: 2 0 0 0 GIC 127 Level 78b5000.spi 80: 0 0 0 0 GIC 357 Edge q6_wdog_interrupt 81: 0 0 0 0 GIC 344 Edge 7803000.sdcc1ice 82: 3 0 0 0 GIC 354 Edge smp2p 83: 0 0 0 0 GIC 276 Edge tzerror 88: 1367 0 0 0 GIC 409 Edge nss_empty_buf_sos 89: 3 0 0 0 GIC 410 Edge nss_empty_buf_queue 90: 0 0 0 0 GIC 411 Edge nss-tx-unblock 91: 65576 0 0 0 GIC 412 Edge nss_queue0 92: 0 0 0 0 GIC 413 Edge nss_queue1 93: 0 0 0 0 GIC 414 Edge nss_queue2 94: 0 0 0 0 GIC 415 Edge nss_queue3 95: 0 0 0 0 GIC 416 Edge nss_coredump_complete 96: 0 0 0 0 GIC 417 Edge nss_paged_empty_buf_sos 97: 616 0 0 0 GIC 422 Edge nss_empty_buf_sos 98: 0 0 0 0 GIC 423 Edge nss_empty_buf_queue 99: 0 0 0 0 GIC 424 Edge nss-tx-unblock100: 62537 0 0 0 GIC 425 Edge nss_queue0101: 0 0 0 0 GIC 426 Edge nss_queue1102: 0 0 0 0 GIC 427 Edge nss_queue2103: 0 0 0 0 GIC 428 Edge nss_queue3104: 0 0 0 0 GIC 429 Edge nss_coredump_complete105: 0 0 0 0 GIC 430 Edge nss_paged_empty_buf_sos106: 0 0 0 0 GIC 35 Level watchdog bark107: 62 0 0 0 GIC 353 Edge qcom,glink-smem-native-xprt-modem108: 0 0 0 0 GIC 239 Level bam_dma109: 62541 0 0 0 GIC 178 Level bam_dma132: 4 0 0 0 GIC 348 Edge ce0133: 16 0 0 0 GIC 347 Edge ce1134: 25 0 0 0 GIC 346 Edge ce2135: 18 0 0 0 GIC 343 Edge ce3137: 11 0 0 0 GIC 443 Edge ce5139: 17 0 0 0 GIC 72 Edge ce7140: 178800 0 0 0 GIC 71 Edge ce8141: 0 0 0 0 GIC 334 Edge ce9142: 0 0 0 0 GIC 333 Edge ce10143: 0 0 0 0 GIC 69 Edge ce11147: 2 0 0 0 GIC 326 Edge host2rxdma-monitor-ring3148: 0 0 0 0 GIC 325 Edge host2rxdma-monitor-ring2149: 2 0 0 0 GIC 324 Edge host2rxdma-monitor-ring1150: 0 0 0 0 GIC 323 Edge reo2ost-exception151: 0 0 0 0 GIC 322 Edge wbm2host-rx-release152: 0 0 0 0 GIC 321 Edge reo2host-status153: 0 0 0 0 GIC 320 Edge reo2host-destination-ring4154: 0 0 0 0 GIC 271 Edge reo2host-destination-ring3160: 1 7 0 0 GIC 263 Edge ppdu-end-interrupts-mac3161: 0 0 0 0 GIC 262 Edge ppdu-end-interrupts-mac2162: 1 0 0 0 GIC 261 Edge ppdu-end-interrupts-mac1163: 3 0 0 0 GIC 260 Edge rxdma2host-monitor-status-ring-mac3164: 0 0 0 0 GIC 256 Edge rxdma2host-monitor-status-ring-mac2165: 3 0 0 0 GIC 255 Edge rxdma2host-monitor-status-ring-mac1167: 0 0 0 0 GIC 215 Edge host2rxdma-host-buf-ring-mac2169: 0 0 0 0 GIC 211 Edge rxdma2host-destination-ring-mac3170: 0 0 0 0 GIC 210 Edge rxdma2host-destination-ring-mac2171: 0 0 0 0 GIC 209 Edge rxdma2host-destination-ring-mac1176: 0 0 0 0 GIC 191 Edge wbm2host-tx-completions-ring3182: 0 0 0 0 GIC 216 Edge tsens_interrupt183: 5 0 0 0 GIC 47 Edge cpr3185: 3 0 0 0 pmic_arb 3211277 Edge spmi-vadc186: 0 0 0 1 smp2p 1 Edge error_ready_interrupt187: 0 0 0 0 smp2p 0 Edge err_fatal_interrupt188: 0 0 0 0 smp2p 3 Edge stop_ack_interrupt189: 0 0 0 0 GIC 172 Edge xhci-hcd:usb1IPI0: 3803 7280 8479 6934 Rescheduling interruptsIPI1: 5 12 11 10 Function call interruptsIPI2: 0 0 0 0 CPU stop interruptsIPI3: 0 0 0 0 Timer broadcast interruptsIPI4: 0 0 0 0 IRQ work interruptsIPI5: 0 0 0 0 CPU wakeup interruptsErr: 0

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies

[OpenWrt Wiki] Xiaomi Redmi AX6 Wi-Fi 6 Mesh Router (2024)
Top Articles
Latest Posts
Article information

Author: Cheryll Lueilwitz

Last Updated:

Views: 6066

Rating: 4.3 / 5 (54 voted)

Reviews: 93% of readers found this page helpful

Author information

Name: Cheryll Lueilwitz

Birthday: 1997-12-23

Address: 4653 O'Kon Hill, Lake Juanstad, AR 65469

Phone: +494124489301

Job: Marketing Representative

Hobby: Reading, Ice skating, Foraging, BASE jumping, Hiking, Skateboarding, Kayaking

Introduction: My name is Cheryll Lueilwitz, I am a sparkling, clean, super, lucky, joyous, outstanding, lucky person who loves writing and wants to share my knowledge and understanding with you.