Post Reply
- Print view
10 posts• Page 1 of 1
- robin.bergen
- Posts: 1
- Joined: Fri Nov 03, 2023 12:49 am
Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby robin.bergen »
Hello,
I am a beginner with SDR and am using a bladeRF xA9 with SDRangel as my spectrum analyzer software. When I am in the device choosing option within SDRangel, I notice there are two bladeRF options available: bladerf[0:0] and bladerf[0:1]. I am having trouble determining which one of these is the receiving port and which one is the transmitting port. I would greatly appreciate it if someone could clarify this for me or point me to where I might find this information. I am still learning and any help would be much appreciated.
Thank you in advance for your help!
Top
- nsk_nyc
- Posts: 1
- Joined: Mon Dec 11, 2023 10:28 pm
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby nsk_nyc »
You can tell because sdrangel will only let you select the antenna based on the device you picked. RX device or TX device. 0 being the first of the two. I hope that didn't confuse you.
Top
- suitwrestlers
- Posts: 1
- Joined: Wed Jan 17, 2024 12:35 am
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby suitwrestlers »
Okay, managed to solve this !
Top
- lilycollins9x
- Posts: 4
- Joined: Mon Jan 08, 2024 9:51 pm
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby lilycollins9x »
Hello! I can help you understand the two options bladerf[0:fnaf0] and bladerf[0:1] in SDRangel. It's great to get started with SDR and use the bladeRF xA9 with SDRangel!
Regarding your question, bladerf[0:0] and bladerf[0:1] do not differentiate in terms of receiving and transmitting ports. Both can be used for both functions, depending on how you configure them in the SDRangel software.
Top
- jenniferlopez1868
- Posts: 2
- Joined: Mon Feb 19, 2024 7:08 pm
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby jenniferlopez1868 »
bladeRF is a USB 3.0-based, next-generation Software Defined Radio (SDR) platform, offering a frequency range of 47 MHz to 6 GHz, 61.44 MHz sampling rate, and 2x2 MIMO streaming.
slope game
Top
- henrkaty
- Posts: 1
- Joined: Thu Apr 04, 2024 9:37 pm
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby henrkaty »
I appreciate your willingness to impart this knowledge to me. I greatly appreciate the blog post that you have authored. slope game free
Top
- soiltrunnel
- Posts: 1
- Joined: Wed Apr 17, 2024 2:13 am
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby soiltrunnel »
You can connect the adc_streams to the dac_streams and change the vhdl code if you require low latencygeometry dash lite. If not, you can use GNURadio, the CLI, or APIs to link RX and Tx to the host or PC.
Top
- kanecharles
- Posts: 1
- Joined: Sat Apr 20, 2024 3:27 am
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby kanecharles »
Based on the information you provided, it seems that you are trying to determine the receiver and transmitter ports for the bladeRF xA9 in SDRangel. The options available to you are "bladerf[0:0]" and "bladerf[0:1]."
Typically, in SDRangel time calculator, the notation "bladerf[0:0]" refers to the receiving (RX) port, while "bladerf[0:1]" refers to the transmitting (TX) port. Therefore, "bladerf[0:0]" is likely the receiving port and "bladerf[0:1]" is the transmitting port.
If you're still unsure, I'd recommend checking the bladeRF xA9 documentation or reaching out to the SDRangel community for further clarification. Good luck with your learning, and I hope this helps!
Top
- cricketgnu
- Posts: 2
- Joined: Wed May 22, 2024 7:25 pm
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby cricketgnu »
If you encounter errors, warnings, or unexpected output, be sure to check the Troubleshooting page before continuing in this guide. For additional information, be sure to check out the bladeRF-cli Tips and Tricks wiki page.drift hunters
Top
- LucyCoffee
- Posts: 3
- Joined: Fri Apr 12, 2024 1:59 am
- Contact:
Contact LucyCoffee
Re: Identifying Receiver and Transmitter Ports in SDRangel for bladeRF xA9
- Quote
Postby LucyCoffee »
In SDRangel, futa sex dollbladerf[0:0] typically represents the receiving (RX) port, while bladerf[0:1] represents the transmitting (TX) port. You can confirm this by checking the bladeRF's configuration or referring to the device's documentation for more detailed information. Happy learning!
Top
Post Reply
- Print view
10 posts• Page 1 of 1
Return to “Software development”
Jump to
- News and Announcements
- ↳ News
- Development
- ↳ Software development
- ↳ Hardware and RF
- ↳ Digital Signal Processing
- ↳ Project showcase
- ↳ Tutorials and Examples
- Troubleshooting
- General
- ↳ Garbage
